HomeView Teardown Finds Glued Speakers and Brittle Connectors

A new HomeView teardown found that Apple glued the display half of its smart home hub down harder than any Apple product opened recently. Getting to the parts destroyed a speaker and a connector, and the speaker base cannot be separated from the display without special tools or a destructive teardown of the screen side.

None of this changes how HomeView works day to day, but it matters when the display or a speaker fails. Apple’s own HomeView repair costs are $279 outside warranty without AppleCare+ and $39 with the plan, so anyone fixing a unit outside Apple has to work around the glue and connectors below. iFixit ran CT scans of both models before opening them, and each step is photographed in its full HomeView teardown.

HomeView’s Display Is Glued Down

Getting to anything behind the HomeView display means going through fragile front glass first, the same as on an iPad. The adhesive held harder than on any recent Apple product, and the aluminum enclosure pulled heat away from the heat mat, which made the softening step slow.

HomeView display being lifted from the enclosure during the teardown
Image: iFixit

The speakers are where the damage started, since their connectors are brittle plastic glued to the board. The leads on the left speaker ripped out of the housing, and the right connector would not come out without damage even after scraping, heat and a knife along the seams. The Steam Deck haptics and the M4 Mac mini power button use the same kind of connector.

HomeView speaker connector with leads torn out of the plastic housing
Image: iFixit

The two large speakers take up most of the space behind the display, and lifting one out was no easier. Thick adhesive pads under the speaker stayed bonded after the area was soaked in isopropyl alcohol, and the speaker snapped in two. Most laptop makers mount speakers with screws and isolation grommets, and Apple’s own MacBook speakers use a lighter adhesive.

HomeView speaker snapped in two during removal
Image: iFixit

Apple uses the aluminum chassis as a heat sink, and a second clipped shield under the logic board carries heat into it. That shield is glued in place, so lifting the board takes a lot of force on a thin piece of hardware. The board holds an A18 chip under 8 GB of SK hynix LPDDR5X memory, plus what looks like 64 GB of Kioxia flash storage.

Apple also mixes screw types. One bracket over the display connector has a Phillips screw on one side and a Torx screw on the other, and the camera bracket needs a larger Torx bit than the rest. The third microphone, under a bracket at the top, is held by a screw and a thin strip of adhesive.

The glue is a step back for Apple. The original HomePod needed a hacksaw to open, the HomePod 2 opened without damage, and recent iPads gained easier battery access, replaceable USB-C ports and official repair manuals.

The HomeView Teardown Found a Better Base

The speaker base is built like a HomePod. The bottom non-slip pad peels away, four Torx screws release the bottom plate, and a taped press connector frees a flex cable that leads to a USB-C port. That port is modular, and the power supply board comes out after a few screws and connectors without a fight against adhesive.

Two passive radiators sit in a metal frame and use the air pressure from the woofer to produce deeper bass. They are modular and would be easy to replace, but the woofer cable is very short and hard to reach, and it is unclear how anyone would reconnect it.

The two halves are the bigger problem. The large Torx screws that hold the pivot to the screen are torqued, covered in threadlocker and sit at an off angle that needs a specific ratchet. Apple routed the interconnect cables through the pivot before those screws went in, so you cannot separate the display from the base without special tools or a destructive teardown of the screen side.

Four Torx screw portal connecting the HomeView display to the speaker base
Image: iFixit

Wall-Mounted HomeView Is Built Differently

Inside, the wall-mounted HomeView differs from the speaker base version. It has extra magnets, a larger logic board of a different shape and a USB-C port that exits at the center. The model with the speaker base has larger speakers and a circular pivot mount.

Newsletter
Never miss an Apple story
One email a day, the news that matters. No spam, unsubscribe anytime.
About the Author

Imran Hussain is the founder and editor of iThinkDifferent, which he launched in 2008 to cover Apple news, reviews, and how-to guides. He has spent over 15 years writing about iOS, macOS, and the wider Apple ecosystem, with a focus on hands-on guides - installing developer betas, troubleshooting, and walking through new features on his own devices. Based in Dubai, he also loves to cover photography, gaming, and the tech industry more broadly on his social media profiles.

Leave a comment